Inficon IMM-200 Скачать руководство пользователя страница 44

Страница: 44 / 67

9 | Troubleshooting and Error Messages

INFICON

44 / 67

074-733-P1A IMM-200 Operating Manual

SYMPTOM

CAUSE

REMEDY

d. Check for thermally

induced electrical shorts or

open conditions.

c. Using an ohmmeter or

DMM, check for electrical

continuity in the sensor

cable, connector, contact

springs, connecting wire

inside sensor, and

feedthroughs.

d. Using an ohmmeter or

DMM, check for electrical

continuity in the sensor

cable, connector, contact

springs, connecting wire

inside sensor, and

feedthroughs.

3. The crystal does not

oscillate or oscillates

intermittently (both in

vacuum and in air).

a. There is intermittent or

poor electrical contact (the

contacts are oxidized).

b. The leaf spring has lost

retentivity (ceramic

retainer, center insulator).

c. There is RF interference

from the sputtering power

supply.

d. The cables are not

connected or are

connected to the wrong

input.

a. Use an ohmmeter or

DMM to check electrical

continuity. Replace the

ceramic retainer.

b. Bend the leaves to

approximately 45

. Refer to

the appropriate sensor

manual.

c. Verify earth ground. The

ground strap should be

adequate for RF ground

(solid copper strap with a

5:1 length:width ratio is

recommended). Change

the location of IMM-200

and move the oscillator

cabling away from RF

power lines. Connect the

IMM-200 power supply to a

different power line.

d. Verify that there are

proper connections.

Содержание IMM-200




































































Результаты поиска

Содержание IMM-200

Отзывы:

Inficon IMM-200, Руководство по эксплуатации, Страница: 44 / 67

Результаты поиска

Содержание IMM-200

Отзывы: