Inficon IMM-200 Скачать руководство пользователя страница 29

Страница: 29 / 67

INFICON

Ethernet Communications | 7

074-733-P1A IMM-200 Operating Manual

29 / 67

7 Ethernet Communications

7.1 Introduction

IMM-200 uses a Lantronix

XPort Ethernet communications interface for sending

parameter values, instrument commands, and status, warning and error messages

between IMM-200 and a host computer. INFICON P3Plus communications protocol

packets with computed CRC are transferred between the IMM-200 and the Lantronix

adapter (8, N, 1, 921600 bps).

7.2 Setting the IP Address

IMM-200 Ethernet settings can be configured using the Lantronix DeviceInstaller

Windows application downloadable from: https://www.lantronix.com/products/

deviceinstaller/

There are a few ways to set the IP address. All of them are described in the User

Guide for the XPort device. https://cdn.lantronix.com/wp-content/uploads/pdf/

DeviceInstaller_UG.pdf

If the IP address is already known, type it into the browser. A prompt appears with a

so leave them blank and click OK to login. The IP address for IMM-200 is under

Network. Make sure that the IP address for the Remote Host (under Channel 1 |

Connection) is set to the same subnet as the new IP. It is not used, but the IP must be

compatible.

If the IP address is unknown, the easiest way to access the device is to install the

Lantronix DeviceInstaller Windows application. It will find all Lantronix devices on the

network. From the factory the default configuration of the Ethernet module is set for an

IP address of 192.168.1.101 and a subnet mask of 255.255.255.0. The DeviceInstaller

may find many Lantronix devices on the network. IMM-200 uses the XPort-05. Once

the XPort device to be modified is selected, use the Web Configuration from within the

app or just use the browser (with the known IP address).

7.3 Protocol

IMM-200 uses the P3Plus (P3P) communication protocol with the following notes:

• ADR byte not evaluated (set to 0)

• ADR byte included in CRC calculation

• DEV ID ignored by slave on Requests to slave.

Содержание IMM-200




































































Результаты поиска

Содержание IMM-200

Отзывы:

Похожие инструкции для IMM-200

Бренды по названию

Популярные бренды

Inficon IMM-200, Руководство по эксплуатации

Результаты поиска

Содержание IMM-200

Отзывы:

Похожие инструкции для IMM-200

Бренды по названию

Популярные бренды