Inficon IMM-200 Скачать руководство пользователя

Страница: 47 / 67

INFICON

Troubleshooting and Error Messages | 9

074-733-P1A IMM-200 Operating Manual

47 / 67

SYMPTOM

CAUSE

REMEDY

c. Check the sensor

magnetic field strength.

The maximum field at the

center of the aperture

should be 700 gauss or

greater.

8. There is a rotary sensor

crystal switch problem.

(The sensor does not

advance or is not centered

in aperture.)

a. There is no relay or an

incorrect relay output

programmed (for

instruments having

outputs).

b. There is a loss of

pneumatic supply or the

pressure is insufficient for

operation.

c. Operation has been

impaired as a result of

material accumulation on

the cover.

d. There is an improper

alignment.

e. A 0.057 mm (0.00225

in.) diameter orifice is not

installed on the supply side

of solenoid valve assembly

(CrystalSix or Crystal12

sensors).

a. Program a relay.

b. Ensure the air supply is

regulated at 80-90 psi.

c. Clean material

accumulation as needed.

d. Refer to the sensor

operating manual for the

alignment procedure.

e. Install the orifice as

shown in the CrystalSix or

Crystal 12 Operating

manual.

9.3 Troubleshooting Computer Communication

Symptom

Cause

Remedy

1. Communication cannot

be established between

the computer and

IMM-200.

a. There is an improper

communication cable

connection.

b. There is a defective

communication cable.

c. The incorrect IP address

or submask being used.

a. Ensure that the cables

are connected to the

correct ports on IMM-200

and the computer.

b. Verify that the cable is

plugged in and is not

damaged. Replace the

communication cable.

Содержание IMM-200




































































Результаты поиска

Содержание IMM-200

Отзывы:

Похожие инструкции для IMM-200

Бренды по названию

Популярные бренды

Inficon IMM-200, Руководство по эксплуатации

Результаты поиска

Содержание IMM-200

Отзывы:

Похожие инструкции для IMM-200

Бренды по названию

Популярные бренды