Inficon IMM-200 Скачать руководство пользователя

Страница: 25 / 67

INFICON

Installation and Interfaces | 5

074-733-P1A IMM-200 Operating Manual

25 / 67

LED State

Description

boot loader flash

(0.4 second on,

0.4 second off)

Normal, a valid firmware version is present.

boot loader flash

(0.2 second on,

0.2second off)

Old firmware is being overwritten, new firmware has

been downloaded and passed the integrity check.

boot loader flash

(0.5 second on,

.2 second off,

.5 second on,

1 second off)

The firmware is invalid.

off

The unit is in diagnostics mode, or the unit has

encountered an error, or no power is applied to the

device.

flash

(1 second on

4 seconds off)

The unit is in idle mode.

blinking

(1 second on

1 second off)

The unit is in Measure mode and a crystal failure has

been detected.

The unit is in Measure mode

or the unit is running normally in boot.

Содержание IMM-200




































































Результаты поиска

Содержание IMM-200

Отзывы:

Похожие инструкции для IMM-200

Бренды по названию

Популярные бренды

Inficon IMM-200, Руководство по эксплуатации

Результаты поиска

Содержание IMM-200

Отзывы:

Похожие инструкции для IMM-200

Бренды по названию

Популярные бренды