Impax 2000 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 55

background image

30

CUSTOMER SERVICE

If you have a problem which cannot be fixed by any of the procedures in this book, do not
hesitate to call IMPAX for service. Often, the problem can be fixed by simple instructions
over the telephone. Before calling, be sure you know all of the facts and symptoms of the
problem, information about the model and program revision numbers of the IMPAX unit,
and the make and the model of the header, roller, or other machine which it controls. This
makes it possible to quickly pinpoint and solve the problem.

Before calling, you should know:

IMPAX Serial number (on side of console): ___-___-___

Software Version: Version_________ (should be in the form of XXXXX-XX)

Definition Package P___TH___D___

*Note: Refer to Chapter 8 of the Supervisor’s Guide for instructions on
accessing the IMPAX software version and definition package.

Machine Make:__________________________

Machine Model:__________________________

Number of Stations:_______________________

«
...
31
32
33
34
35
...
»

Содержание 2000
























































Отзывы:

Нет отзывов

Похожие инструкции для 2000

Бренд: babymoov Страницы: 2

Бренд: babymoov Страницы: 40

Бренд: IBM Страницы: 35

ThinkVision L180p

Бренд: IBM Страницы: 28

Бренд: IBM Страницы: 23

Бренд: IBM Страницы: 4

Бренд: IBM Страницы: 30

LCD3215 - MultiSync - 32" LCD Flat Panel...

Бренд: NEC Страницы: 34

Бренд: Citizen Страницы: 10

Бренд: Daktronics Страницы: 79

Odyssey S27AG550EN

Бренд: Samsung Страницы: 36

Odyssey Ark Series

Бренд: Samsung Страницы: 42

Бренд: Samsung Страницы: 36

Odyssey S49CG954SU

Бренд: Samsung Страницы: 24

Бренд: Vicon Страницы: 24

VG910B - 19" LCD Monitor

Бренд: ViewSonic Страницы: 21

Бренд: ViewSonic Страницы: 25

Бренд: Lanaform Страницы: 312

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды