Impax 2000 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 55

background image

31

Chapter 7 - Programming for the IMPAX 2000

Introduction

This section is provided as a guide to the IMPAX Version 58 software. It is not intended to replace
training, but rather to guide the user through changes they may choose to make in the options
available in the IMPAX Versions 58 Software. Every effort has been made to assure accuracy and
completeness.

This section makes a few assumptions. First and most important, is that the user has had some
IMPAX training. If you feel that your level of training is not what it should be, please contact
Process Technologies Group, Inc.

Since there are several combinations of selections, we must have a starting point. In the interest of
simplicity, we assume that you have 8 channel software with the Standard Program initiated. A few
words about the Standard Program are in order.

The Standard Program is the set of options in the software program, as they were set when the
program was installed in the IMPAX unit at the factory. These options man have been customized
for your particular application when the IMPAX was tested or installed. If the prompts shown in
this guide differ from the prompts on your IMPAX unit, this may be due to changes made by the
installer at the time of installation. These changes were made for good reasons and may be
necessary for the proper operation of your IMPAX system. We suggest that you carefully consider
your changes before changing a "custom" setup, and that you document the changes, using the Setup
Sheet located in the back of this section, in case you need to change them back.

Before getting started, it would be good to review some things that are common to previous versions
of IMPAX software, such as using the alphanumeric keypad, and to cover some new material which
will be used later when we go through the program options step by step.

*Next can also be used to answer "No"
*Enter can also be used to answer "Yes"
*The

Supervisor's Key

is on when it is turned to the right, i.e. in the horizontal position.

*"ACCESS DENIED" is displayed when the wrong access code has been entered, or
when the new number has not been correctly entered (when changing the access code)

Generally, pressing Next will toggle such displays as "ON/OFF" or "ENABLE/DISABLE". Next
will also step through the displays offering choices such as Tag Names, Relay Names or Channel
Names.

«
...
32
33
34
35
36
...
»

Содержание 2000
























































Отзывы:

Нет отзывов

Похожие инструкции для 2000

Бренд: Samsung Страницы: 48

743BX - SyncMaster - 17" LCD Monitor

Бренд: Samsung Страницы: 80

740N - SyncMaster - 17" LCD Monitor

Бренд: Samsung Страницы: 55

740BF - SyncMaster - 17" LCD Monitor

Бренд: Samsung Страницы: 82

740BX - SyncMaster - 17" LCD Monitor

Бренд: Samsung Страницы: 77

730MW - SyncMaster - 17" LCD Monitor

Бренд: Samsung Страницы: 61

Бренд: Samsung Страницы: 28

730B - SyncMaster - 17" LCD Monitor

Бренд: Samsung Страницы: 69

720N - SyncMaster - 17" LCD Monitor

Бренд: Samsung Страницы: 43

65" 650TS Interactive Whiteboard LCD

Бренд: Samsung Страницы: 29

710N - SyncMaster 17" LCD Monitor

Бренд: Samsung Страницы: 93

460UTN-UD - 46" LCD Video Wall Display

Бренд: Samsung Страницы: 24

400UXN-UD - 40IN LCD 5000:1 1366X768

Бренд: Samsung Страницы: 25

400TSN-2 - 40" LCD Touch

Бренд: Samsung Страницы: 21

320TSN-2 - 32" - LCD Touch Screen

Бренд: Samsung Страницы: 126

305T - SyncMaster - 30" LCD Monitor

Бренд: Samsung Страницы: 33

275T - SyncMaster - 27" LCD Monitor

Бренд: Samsung Страницы: 61

245T - SyncMaster - 24" LCD Monitor

Бренд: Samsung Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды