Impax 2000 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 55

background image

14

Chapter 4 - IMPAX Information Displays

Quantity

MADE * 750

Next/No

TO GO * 99250

Next/No

SHIFT * 750

Next/No

B MADE * 750

Next/No

B TO GO * 4250

Next/No

EXPTS

Next/No

RPM 300

Useful information is available from the IMPAX console simply by pressing buttons. This may
be done whether the machine is running or stopped. Unless otherwise instructed, the

Supervisor’s Key

should be removed or turned to the vertical position while performing these

steps.

To inquire about Quantity settings or production totals, Tolerance settings, Error conditions
which have occurred, or Force measurements and limits, press the appropriate button.

Quantity Displays:

Press Quantity. The display will show
“MADE * 750” if 750 parts have been
produced on this job. If the machine is
running and the green light is on, the
number will be counting up.

Press Next/No again and the display
changes to “TO GO * 99250”, which is
the number of parts remaining to be
made. This number counts down when
the machine is running.

Press Next/No again and the display
changes to “SHIFT * 750”, which
means that 750 parts have been made
during the current shift.

Press Next again and IMPAX shows “B
MADE * 750”, which means that 750
parts have been made during the current
shift.

Press Next/No again and the display
becomes “B TO GO * 4250”, meaning
that 4250 more pieces will be made
before the machine is stopped for an
inspection break. This also counts
down. If exceptions are turned on in
Channel Definition, then the next
display will show them.

Press Next/No and the display will
show “RPM 300” which is the speed
that the machine is running at.

Press Display Will Show

Pressing Enter will start Autoscroll, pressing Enter
again will stop it on the current screen. During
scroll, Next/No will not work.

If exceptions are turned on:

«
...
15
16
17
18
19
...
»

Содержание 2000
























































Отзывы:

Нет отзывов

Похожие инструкции для 2000

CYVMX6800U - 6.8" CLR MONITOR/DVD

Бренд: Panasonic Страницы: 4

Intelli sense 7300REL

Бренд: ReliOn Страницы: 88

Бренд: Daewoo Страницы: 75

Бренд: Samtron Страницы: 57

Бренд: Hanns.G Страницы: 2

Hanns G HL225PPB

Бренд: HANNspree Страницы: 20

Бренд: weintek Страницы: 8

Бренд: CORNEA Страницы: 20

Бренд: G-STORY Страницы: 41

Бренд: AOR Страницы: 39

COLORSMART BB-3102

Бренд: Daktronics Страницы: 108

Бренд: Pyle view Страницы: 20

Бренд: ViewSonic Страницы: 26

Бренд: AOC Страницы: 77

ProLite T2234MSC

Бренд: Iiyama Страницы: 31

Bay Cat X SN-4620-1080

Бренд: Planar Страницы: 159

Бренд: Lanix Страницы: 80

Бренд: Raymarine Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды