Impax 2000 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 55

background image

Setting Tolerances - cont.

10

Enter/Yes

C1 TREND 0%

5

C1 TREND 50%

X

Enter/Yes

(Next option or channel)

Next/No

(Next option or channel)

Enter/Yes

(Next option or channel)

ALL FACTORS SET

Trend Setting

After the Tolerance has been set for the
first channel, press the Enter/Yes key.
If Trending is turned on in Channel
Definition, the next display will show
“C1 TREND 0%”. By entering a
number here from 1 to 99, you can limit
the amount that the force measurement
can drift due to gradual changes such as
tool wear. For example, pressing 50
displays “C1 TREND 50%”, which will
stop the machine after the force changes
(gradually) by 50%; you would then
clean or replace the tool. Set the Trend
Factor by pressing the Enter/Yes key.

Exception Setting

If Exceptions are turned on in Channel
Definition, the next display will show
either “C1 CUMU EX 0" or “C1
CONS EX 0." An exception is an
IMPAX detected error which you can
allow the monitor to ignore. This
feature is extremely useful if you have a
diverter installed on the machine. If a
diverter is installed, you can set one of
the relays to be an exception relay and it
will trip the diverter and divert the part
without stopping the machine.

“CUMU” stands for cumulative. This
means that IMPAX will allow a certain
number of errors out of 100 to be
ignored. For example, if I set the
number to 2, IMPAX would allow 2
parts out of 100 to exceed either the HI
or the LO limit without shutting down
the machine.

“CONS” stands for consecutive. This
means that IMPAX will allow a certain
number of errors in a row to be ignored.

Press Display Will

Show

(Trend can be set from 1% to 99%)
For Example:

These options will only be available if

turned on in Channel Definition in

programming.

To permit exceptions, backstrokes, and/or low

force readings:

(All described below)

X can be from 1 to 9,999

To not permit exceptions, backstrokes, and/or

low force readings:

or

Once all tolerances, fixed limits, excpts, nofeeds,

and trend information is set:

«
...
12
13
14
15
16
...
»

Содержание 2000
























































Отзывы:

Нет отзывов

Похожие инструкции для 2000

Бренд: Bang & Olufsen Страницы: 65

Бренд: PanelPilot Страницы: 10

Бренд: Chassis Plans Страницы: 72

Бренд: I-Tech Страницы: 18

Бренд: Uniden Страницы: 44

Бренд: BABY DELIGHT Страницы: 13

MultiSync FE700+

Бренд: NEC Страницы: 64

Бренд: CORNEA Страницы: 20

Бренд: Foscam Страницы: 2

Бренд: Dantherm Страницы: 84

ProcessViewDisplay ME61

Бренд: Burkert Страницы: 24

Бренд: Lorex Страницы: 15

FlexScan S2100-M

Бренд: Eizo Страницы: 38

FlexScan EV2457

Бренд: Eizo Страницы: 43

Бренд: Daewoo Страницы: 54

Adaptive FAST-12

Бренд: Tapco Страницы: 16

Бренд: Absen Страницы: 52

Бренд: INNOLIVING Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды