IKA 0005020000, Руководство по эксплуатации

Страница: 33 / 136

33
Error messages and troubleshooting table
Fault Description Causes Effect Solutions
Er 2 In remote operation (PC)
mode with activated
watchdog function in
mode 1: no communica-
tion between PC and RET
control-visc
• PC does not transmit any data
within the set watchdog time
• Connection to PC interrupted
Heating switched off
Motor switched off
• Change watchdog time
• Transmit data from PC within set
watchdog time (OUT_WDx@m)
• Check cable and plug
Er 3 Device internal tempera-
ture exceeds 80 °C
• Heat accumulation between
heating plate and housing
• Permitted ambient temperature
exceeded
Heating switched off • Switch device off, leave to cool and
switch on again
• Change experiment
• Observe maximum permissible am-
bient temperature
Er 4 Difference between target
and actual speed exceeds
300 rpm
• Motor blocked or overloaded Heating switched off
Motor switched off
• Reduce load torque or use smaller
magnetic rods
• Reduce target speed
Er 5 No temperature increase
in sensor at continuous
temperature difference
(selected time in menu)
• Sensor not in medium
• Volume of medium to be mea-
sured too large
• Heat conductivity of medium to
be measured too low
• Heat conductivity of the vessel is
too low
• In the case of indirect heating,
the overall heat conductivity re-
sistance is too large
Heating switched off • Place the sensor in the medium
• Reduce the volume of the media
• Use a carrier fluid with better heat
conductivity properties
• Replace the glass vessel with a
metal pot
• Increase the “Time-out” period
Er 6 Interruption in safety cir-
cuit
• Defective connection cable Heating switched off • Replace cable
Er 13 SAFE TEMP P adjustable
safety circuit defective
• Target/current different of the
adjustable safety circuit for mini-
mum temperature monitoring
Heating switched off • After switching on, change the
SAFE TEMP to a different value; if
this solves the issue, the previous
value can be reset by switching the
device off and on again
Er 14 Short circuit in temperatu-
re sensor 1
• Short circuit in temperature sen-
sor plug
• Short circuit in the cable or tem-
perature sensor
Heating switched off • Check the plug
• Replace the temperature sensor
Er 21 Fault during heating plate
safety test
• Safety relay does not open Heating switched off • Switch device off, leave to cool and
switch on again
Er 22 Fault during heating plate
safety test
• S_CHECK cannot generate
H_S_TEMP
Heating switched off • Switch device off, leave to cool and
switch on again
Er 24 The temperature of the
heating plate exceeds
SAFE TEMP H (Hotplate)
• SAFE TEMP H (Probe) has been
set to lower than the current tem-
perature of the heating plate
• Disconnection of heating plate
control temperature sensor
Heating switched off • Leave the heating plate to cool
• Set the SAFE TEMP H (Hotplate)
higher
Troubleshooting
The device will indicate that there is a fault by displaying an error
message “Er X” (see table) on the screen.
Heating will be switched off permanently (exception: WD - see
table).
The stirring function continues to operate at the pre-set speed if
there is a fault in the heating circuit (exception: WD - see table).
In order to reset the device after a fault, it may need to be discon-
nected from the power supply for several seconds. The period the
device is switched off may also need to be longer if the tempera-
tures need to be counterbalanced (residual heat display may no
longer be active; see “Residual heat display”).
The safety circuit test takes place within 20 seconds of switching
on the device; after the test, the other monitoring functions are
activated.
If a fault cannot be eliminated directly, you must perform a
RESET (see “Settings” menu) . If the faults still cannot be elimi-
nated, the appliance must be inspected by a technical service
technician.