IEI Technology KINO-ATOM Скачать руководство пользователя страница 99

Страница: 99 / 202

KINO-ATOM Motherboard

Page 81

The optional 7.1 channel audio kit connects to the 10-pin audio connector on the

KINO-ATOM. The audio kit consists of five audio jacks. One audio jack, Mic In, connects

to a microphone. The remaining four audio jacks, Line-In, Front-Out, Rear-Out, and

Center Subwoofer, connect to speakers. To install the audio kit, please refer to the steps

below:

Step 1:

Connect the audio kit cable.

The audio kit is shipped with a cable that

connects the audio kit to the KINO-ATOM. Connect the cable to the connector

on the back of the audio kit. Make sure the pins are properly aligned (i.e. pin 1

connects to pin 1).

Step 2:

Locate the audio connector

. The location of the 10-pin audio connector is

shown in

Chapter 3

Step 3:

Align pin 1

. Align pin 1 on the on-board connector with pin 1 on the audio kit

cable connector. Pin 1 on the audio kit cable connector is indicated with a white

dot. See Figure 5-10.

Figure 5-10: 7.1 Channel Audio Kit

Step 4:

Mount the audio kit onto the chassis

. Once the audio kit is connected to the

KINO-ATOM, secure the audio kit bracket to the system chassis.

Содержание KINO-ATOM











































































































































































































Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology KINO-ATOM, Руководство пользователя

Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды