manualshive.com logo in svg

IEI Technology KINO-ATOM, Руководство пользователя

Поделиться
Скачать
IEI Technology KINO-ATOM Скачать руководство пользователя страница 114

 

 

KINO-ATOM Motherboard

Page 96 

Key 

Function 

F1 key 

General help, only for Status Page Setup Menu and Option 

Page Setup Menu 

F2 /F3 key 

Change color from total 16 colors.    F2 to select color 

forward. 

F10 key 

Save all the CMOS changes, only for Main Menu   

Table 6-1: BIOS Navigation Keys 

6.1.3 Getting Help 

When 

F1

 is pressed a small help window describing the appropriate keys to use and the 

possible selections for the highlighted item appears. To exit the Help Window press 

E

SC

 or 

the 

F1

 key again. 

6.1.4 Unable to Reboot After Configuration Changes 

If the computer cannot boot after changes to the system configuration is made, CMOS 

defaults. Use the jumper described in 

Chapter 5

. 

6.1.5 BIOS Menu Bar 

The 

menu bar

 on top of the BIOS screen has the following main items: 

 

Main 

Changes the basic system configuration. 

 

Advanced

 

Changes the advanced system settings.

 

 

PCIPnP 

Changes the advanced PCI/PnP Settings

 

 

Boot 

Changes the system boot configuration.

 

 

Security 

Sets User and Supervisor Passwords.

 

 

Chipset 

Changes the chipset settings. 

 

Power 

Changes power management settings.

 

 

Exit 

Selects exit options and loads default settings

 

The following sections completely describe the configuration options found in the menu 

items at the top of the BIOS screen and listed above. 

Содержание KINO-ATOM











































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды