IEI Technology KINO-ATOM Скачать руководство пользователя страница 47

Страница: 47 / 202

KINO-ATOM Motherboard

Page 29

CPU temperature

System temperature

The KINO-ATOM Super I/O Enhanced Hardware Monitor also monitors the following fan

speeds:

CPU Fan speed

Voltage inputs on the KINO-ATOM Super I/O Enhanced Hardware Monitor monitors the

following voltages:

CPU Core

+1.05 V

+3.30 V

+5.00 V

+12 V

+1.5 V

+1.8 V

+5 VSB

VBAT

The values for the above environmental parameters are all recorded in the BIOS

Hardware Health Configuration menu.

2.7.2 Operating Temperature and Temperature Control

The maximum and minimum operating temperatures for the KINO-ATOM are listed below.

Minimum Operating Temperature: 0ºC (32°F)

Maximum Operating Temperature: 60°C (140°F)

A cooling fan and heat sink must be installed on the CPU. Thermal paste must be

smeared on the lower side of the heat sink before it is mounted on the CPU. Heat sinks

are also mounted on the Northbridge and Southbridge chipsets to ensure the operating

temperature of these chips remain low.

Содержание KINO-ATOM











































































































































































































Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology KINO-ATOM, Руководство пользователя

Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды