IEI Technology KINO-ATOM Скачать руководство пользователя страница 130

Страница: 130 / 202

KINO-ATOM Motherboard

Page 112

CPU Temp. Limit of OFF

CPU Temp. Limit of Start

CPU Fan Start PWM

Slope PWM 1

When the

CPU FAN Mode Setting

option is in the

PWM Manual Mode

, the following

parameters can be set.

CPU Fan PWM control

CPU Temp. Limit of OFF [000]

WARNING:

Setting this value too high may cause the fan to stop when the CPU is

at a high temperature and therefore cause the system to be damaged.

The

CPU Temp. Limit of OFF

option can only be set if the

CPU FAN Mode Setting

option is set to

Automatic Mode

. Use the

CPU Temp. Limit of OFF

option to select the

CPU temperature at which the cooling fan should automatically turn off. To select a value,

select the

CPU Temp. Limit of OFF

option and enter a decimal number between 000 and

127. The temperature range is specified below.

Minimum Value: 0°C

Maximum Value: 127°C

CPU Temp. Limit of Start [020]

WARNING:

Setting this value too high may cause the fan to start only when the

CPU is at a high temperature and therefore cause the system to be

damaged.

Содержание KINO-ATOM











































































































































































































Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology KINO-ATOM, Руководство пользователя

Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды