IEI Technology KINO-ATOM Скачать руководство пользователя страница 6

Страница: 6 / 202

KINO-ATOM Motherboard

Page vi

Packing List

NOTE:

If any of the components listed in the checklist below are missing,

please do not proceed with the installation. Contact the IEI reseller or

vendor you purchased the KINO-ATOM from or contact an IEI sales

representative directly. To contact an IEI sales representative, please

send an email to

[email protected]

The items listed below should all be included in the KINO-ATOM package.

1 x KINO-ATOM Mini-ITX Motherboard

1 x Dual RS-232 cable (P/N: 32200-028401-RS)

2 x SATA cable (P/N: 32000-062800-RS)

1 x I/O shielding (P/N: 45014-0008C0-00-RS)

1 x Mini jumper pack

1 x Utility CD

1 x QIG (quick installation guide)

Images of the above items are shown in

Chapter 3

Содержание KINO-ATOM











































































































































































































Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology KINO-ATOM, Руководство пользователя

Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды