manualshive.com logo in svg

IEI Technology KINO-ATOM, Руководство пользователя

Поделиться
Скачать
IEI Technology KINO-ATOM Скачать руководство пользователя страница 86

 

 

KINO-ATOM Motherboard

Page 68 

contact the KINO-ATOM vendor reseller/vendor where the KINO-ATOM was purchased or 

contact an IEI sales representative. 

5.4 SO-DIMM Installation 

 WARNING: 

Using incorrectly specified SO-DIMM may cause permanently damage 

the KINO-ATOM. Please make sure the purchased SO-DIMM complies 

with the memory specifications of the KINO-ATOM. SO-DIMM 

specifications compliant with the KINO-ATOM are listed in Chapter 2. 

To install a SO-DIMM into a SO-DIMM socket, please follow the steps below and refer to 

Figure 5-1

. 

 

Figure 5-1: SO-DIMM Installation   

Step 1: 

Locate the SO-DIMM socket

. Place the KINO-ATOM on an anti-static pad with 

the solder side facing up. 

Step 2: 

Align the SO-DIMM with the socket

. The SO-DIMM must be oriented in such a 

way that the notch in the middle of the SO-DIMM must be aligned with the 

plastic bridge in the socket. 

Содержание KINO-ATOM











































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды