IEI Technology KINO-ATOM Скачать руководство пользователя страница 181

Страница: 181 / 202

KINO-ATOM Motherboard

Page 163

LCD

Liquid crystal display (LCD) is a flat, low-power display device that

consists of two polarizing plates with a liquid crystal panel in between.

LVDS

Low-voltage differential signaling (LVDS) is a dual-wire, high-speed

differential electrical signaling system commonly used to connect LCD

displays to a computer.

POST

The Power-on Self Test (POST) is the pre-boot actions the system

performs when the system is turned-on.

RAM

Random Access Memory (RAM) is volatile memory that loses data when

power is lost. RAM has very fast data transfer rates compared to other

storage like hard drives.

SATA

Serial ATA (SATA) is a serial communications bus designed for data

transfers between storage devices and the computer chipsets. The SATA

bus has transfer speeds up to 1.5 Gb/s and the SATA II bus has data

transfer speeds of up to 3.0 Gb/s.

S.M.A.R.T

Self Monitoring Analysis and Reporting Technology (S.M.A.R.T) refers to

automatic status checking technology implemented on hard disk drives.

UART

Universal Asynchronous Receiver-transmitter (UART) is responsible for

asynchronous communications on the system and manages the system’s

serial communication (COM) ports.

UHCI

The Universal Host Controller Interface (UHCI) specification is a

USB

The Universal Serial Bus (USB) is an external bus standard for

interfacing devices. USB 1.1 supports 12 Mb/s data transfer rates and

USB 2.0 supports 480 Mb/s data transfer rates.

VGA

The Video Graphics Array (VGA) is a graphics display system developed

by IBM.

Содержание KINO-ATOM











































































































































































































Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology KINO-ATOM, Руководство пользователя

Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды