IEI Technology KINO-ATOM Скачать руководство пользователя страница 46

Страница: 46 / 202

KINO-ATOM Motherboard

Page 28

2.6.2.6 Keyboard/Mouse Controller

The Super I/O keyboard/mouse controller can execute the 8042 instruction set. Some of

the keyboard controller features are listed below:

The 8042 instruction is compatible with a PS/2 keyboard and PS/2 mouse

Gate A20 and Keyboard reset output

Supports multiple keyboard power on events

Supports mouse double-click and/or mouse move power on events

2.6.2.7 Parallel Port

The multi-mode high-performance parallel port supports the bi-directional Standard

Parallel Port (SPP), the Enhanced Parallel Port (EPP) and the Extended Capabilities Port

(ECP) modes.

2.6.3 Fintek F81216D LPC Serial Port Chipset

The Fintek F81216D chipset enables the addition of two additional UART serial ports

(COM3 and COM4). UART includes 16-byte send/receive FIFO. The Fintek F81216D

serial port chipset is interfaced to the Southbridge chipset through the LPC bus. Some of

the features of the Fintek F81216D chipset are listed below:

Supports LPC interface

Totally provides 4 UART (16550 asynchronous) ports

3 x Pure UART

1 x UART+IR

One Watch dog timer with WDTOUT# signal

One Frequency input 24/48MHz

2.7 Environmental and Power Specifications

2.7.1 System Monitoring

Two thermal inputs on the KINO-ATOM Super I/O Enhanced Hardware Monitor monitors

the following temperatures:

Содержание KINO-ATOM











































































































































































































Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology KINO-ATOM, Руководство пользователя

Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды