IEI Technology KINO-ATOM Скачать руководство пользователя страница 30

Страница: 30 / 202

KINO-ATOM Motherboard

Page 12

Intel® Streaming SIMD Extensions-2 and -3 (Intel® SSE2 and Intel® SSE3)

support and Supplemental Streaming SIMD Extension 3 (SSSE3) support

Micro-FCBGA8 packaging technologies

Thermal management support via Intel® Thermal Monitor 1 and Intel Thermal

Monitor 2

FSB Lane Reversal for flexible routing

Supports C0/C1(e)/C2(e)/C4(e)

L2 Dynamic Cache Sizing

Advanced power management features including Enhanced Intel

SpeedStep® Technology

Execute Disable Bit support for enhanced security

2.3.3 Front Side Bus (FSB)

The Intel® Atom™ processor on the KINO-ATOM is interfaced to the Intel® 945GSE

Northbridge through a 533 MHz front side bus (FSB). The FSB is shown in

Figure 2-5

below.

Figure 2-5: Front Side Bus

Содержание KINO-ATOM











































































































































































































Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology KINO-ATOM, Руководство пользователя

Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды