ICRealtime Edge IPEG-D20F-IRW3 Скачать руководство пользователя страница 112

Страница: 112 / 200

Step 2

Configure date and time parameters.

Table 4-37 Description of date and time parameters

Parameter

Description

Date Format

Configure the date format.

Time Format

Configure the time format. You can select from

12-Hour

24-Hour

Time Zone

Configure the time zone that the camera is at.

Current Time

Configure system time.
Click

Sync PC

, to change the IPC time to the PC time.

Parameter

Description

DST

Enable DST as needed.
Select the checkbox, and configure start time and end time of DST
with

Date

Week

NTP

Select the checkbox to enable NTP (network time protocol) IPC

will then sync time with the internet server.You can also enter
the IP address, time zone, port, and interval of a PC with an
installed NTP server to use NTP.

NTP Server

Time Zone

Port

Interval
Positioning System
Time
Synchronization

Select

Position System Time Synchronization

and configure

Interval

to enable this function. After enabling this function, the device
will synchronize the system time according to the interval you
set.

Interval

Step 3

Click

Save

100

Содержание Edge IPEG-D20F-IRW3









































































































































































































Результаты поиска

Содержание Edge IPEG-D20F-IRW3

Отзывы:

Похожие инструкции для Edge IPEG-D20F-IRW3

Бренды по названию

Популярные бренды

ICRealtime Edge IPEG-D20F-IRW3, Руководство пользователя

Результаты поиска

Содержание Edge IPEG-D20F-IRW3

Отзывы:

Похожие инструкции для Edge IPEG-D20F-IRW3

Бренды по названию

Популярные бренды