![background image](http://html1.mh-extra.com/html/icp-das-usa/isagraf-pac-series/isagraf-pac-series_getting-started_3826573008.webp)
8
Getting Started:
PAC-5007/5107/5207/5307 Ver. 1.1, 12/2011 ICP DAS
Modbus RTU/ASCII Master
Protocol
Max. 2 COM Ports
: COM1, COM2 and COM3
(*)
.
(To connect to other Modbus Slave devices)
Max. Modbus_xxx Function Block amount for 2 ports: 128.
Modbus RTU Slave
Protocol
Max. 2 COM Ports
, COM1 and one of (COM2, COM3)
(*)
.
For connecting ISaGRAF, PC/HMI/OPC Server & MMI panels.
Modbus TCP/IP
Protocol
Max. 6 connections
, Ethernet ports support Modbus TCP/IP Slave Protocol
for connecting ISaGRAF & PC/HMI.
Remote I/O
One of COM2 or COM3 (RS-485)
(*)
supports I-7000 I/O modules & (I-87Kn
or RU-87Pn + I-87K High Profile I/O boards) as Remote I/O. Max.
64
I/O
modules for one PAC.
Fbus
Built-in COM2 Port to exchange data between ICP DAS's ISaGRAF PACs.
Ebus
To exchange data between ICP DAS's ISaGRAF Ethernet PACs via Ethernet
port.
Send Email
Actively or passively sending E-mail via Ethernet port through internet.
Max.10 receivers for each sending and can send E-mail with an attached file.
(Max. file size is about 488 KB)
SMS:
Short Message Service
One of COM1 or COM3 (RS-232)
(*)
can link to a GSM modem to support
SMS. User can request data/control the controller by cellular phone. The
controller can also send data & alarms to user's cellular phone.
Optional
GSM modem
: GTM-201-RS232 (GSM/GPRS 850/900/1800/1900)
Note: μPAC-5207, 5307 has built-in GPRS, no external GSM/GPRS modem
required.
Redundancy Solution
Two PACs plug with
XW107
in slot0. One is Master, one is Slave. Master
handles all inputs & outputs at run time. If Master is damaged (or power off),
Slave will take over the control of Bus7000b. If Master is alive from damaged
(or power up again), it takes the control of Bus7000b again. The change over
time is about 5 seconds. Control data is exchanging via Ebus (if using a cross
cable, no require any Ethernet Switch). All I/O should be RS-485 I/O except
the status I/O in the slot 0: XW107.
CAN/CANopen
Use COM1 or COM3 ~ COM8
(*)
to connect one I-7530 (RS-232 to CAN
converter) to support CAN/CANopen devices and sensors. One PAC supports
max.
3
RS-232 ports to connect max.
3 I-7530
modules. Please refer to:
www.icpdas.com > FAQ > Software > ISaGRAF Ver.3 (English)
Optional I/O Functions
PWM Output
Pulse Width Modulation
Output
support PWM output. Max. 8 channels for one controller.
500 Hz max. for Off = 1 & On = 1 ms
Output square wave: Off: 1 ~ 32767 ms, On: 1 ~ 32767 ms
Counters
Parallel DI Counter
Max. 8 channels for one controller. Counter value: 32-bit
500 Hz max. Min. ON & OFF width must > 1 ms
Remote DI Counter
All remote I-7000 & I-87K DI modules support counters. 100 Hz max.
value: 0 ~ 65535
Remote High Speed
Counter
Optional I-87082: 100 kHz max. ,32-bit
*Note: