v
200 – 240 VAC, 50–60 Hz (two branch circuits) when configured with 192
16-Gbps ports (four circuits required for high availability if configured with
384 16-Gbps ports)
v
Two or four cables for 200 - 240 VAC service
v
Protected by a circuit breaker in accordance with local electrical codes
v
Supply circuit, line fusing, and wire size adequate to the electrical rating on
the chassis nameplate
v
Location close to the chassis and easily accessible
v
Grounded outlets installed by a licensed electrician, compatible with the
power cords
Attention:
To maximize fault tolerance, connect each power cord to a
separate power source.
5.
Ensure that the following are available for configuration of the chassis:
v
Workstation with an installed terminal emulator, such as HyperTerminal
v
Serial cable (provided)
v
Three Ethernet cables (including one spare)
v
Access to an FTP server for backing up the switch configuration or collecting
supportsave output data (optional)
v
SFPs (provided) and compatible cables
6.
Ensure that the air intake and exhaust vents have a minimum of 2 in. of
airspace.
7.
Ensure that the air temperature on the air intake side is less than 40 degrees
Celsius (104 degrees Fahrenheit) during operation.
CAUTION:
Use safe lifting practices when moving the product. (C015)
Note:
A fully populated SAN768B-2 (eight FC8-64 or FC16-64 port cards, 512
ports) weighs approximately 159.2 kg (351 lb) and requires the specified lift tool
to install it.
Installing a SAN768B-2 in a cabinet
This section describes how to install the SAN768B-2 in the Model C36 cabinet.
These procedures use parts that are included in the 14U rack mount kit.
Time required
Allow approximately 4 hours to complete this procedure. This includes unpacking,
assembling, and repacking the lift tool. This is for the physical installation of the
SAN768B-2 only. It does not include installing Ethernet cables, SFPs, attaching and
routing the fiber optic cables, or completing the initial configuration.
Attention:
Attention: If optional feature FC 7230, FIPS 140-2 Level 2 Tamper
Proof Seals is also ordered, be sure to sequence the installation steps to allow for
application of the FIPS seals on the chassis prior to installing the chassis in a rack.
These locations may be difficult to access once the chassis is installed. Refer to the
IBM System Storage FIPS 140-2 Security Seal Application Procedures
(GA32-2220-00) publication for complete instructions.
Table 3 on page 17 provides a summary of time estimates for the different
installation tasks and the tools required for each task. Times may differ, depending
on experience level and your specific configuration.
16
SAN768B-2 Installation, Service, and User Guide
Содержание SAN768B-2
