IBM Elastic Storage System 3200 Скачать руководство пользователя страница 46

Страница: 46 / 156

Table 4. Power cord feature codes (continued)
Feature codes

Description

END1

Power Cord 2.7 m (9 ft), Drawer to IBM PDU (250V/

10A) C13/C14 (6671)

6672

Power Cord 2 m (6.5 ft), Drawer to IBM PDU (250V/

10A) C13/C14

6665

Power Cord 2.8 m (9.2 ft), Drawer to IBM PDU

(250V/10A) C13/C20

Attention: Ensure that sufficient power supply circuits are available to provide the total power

requirements of the equipment that is connected to each power supply circuit.

EMS node power planning

The following table lists the documentation that can be used as a reference while planning for power

requirements.

Table 5. Power planning reference information
For this information...

Go to...

Planning for power for EMS node

https://www.ibm.com/docs/en/power9?topic=shp-

planning-power-8

Determining your power requirements

https://www.ibm.com/docs/en/power9?topic=pp-

determining-your-power-requirements-8

Server Information Form 3A

https://www.ibm.com/docs/en/power9?

topic=dypr-server-information-form-3a-8

Workstation Information Form 3B

https://www.ibm.com/docs/en/power9?

topic=dypr-workstation-information-form-3b-8

Plugs and receptacles

https://www.ibm.com/docs/en/power9?topic=pp-

plugs-receptacles-8

Supported power cords

https://www.ibm.com/docs/en/power9?topic=pr-

supported-power-cords-8

Modification of IBM-provided power cords

https://www.ibm.com/docs/en/power9?topic=pp-

modification-provided-power-cords-8

Uninterruptible power supply

https://www.ibm.com/docs/en/power9?topic=pp-

uninterruptible-power-supply-8

Power distribution unit and power cord options for

7014, 7953, and 7965 racks

https://www.ibm.com/docs/en/power9?

topic=pp-power-distribution-unit-power-cord-

options-7014-7953-7965-racks-9

Calculating the power load for 7188 or 9188 power

distribution units

https://www.ibm.com/docs/en/power9?topic=pp-

calculating-power-load-7188-9188-power-

distribution-units-9

Planning for cables

https://www.ibm.com/docs/en/power9?topic=shp-

planning-cables-8

Power cord routing and retention

https://www.ibm.com/docs/en/power9?topic=cm-

power-cord-routing-retention-8

28 IBM Elastic Storage System 3200: Hardware Planning and Installation Guide

Содержание Elastic Storage System 3200





























































































































































Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды

IBM Elastic Storage System 3200, Руководство по планированию и установке оборудования

Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды