IBM Elastic Storage System 3200 Скачать руководство пользователя страница 3

Страница: 3 / 156

Contents

Figures................................................................................................................ vii

Tables................................................................................................................ xiii

About this information......................................................................................... xv

Who should read this information..............................................................................................................xv

IBM Elastic Storage System information units.......................................................................................... xv

Related information....................................................................................................................................xv

Conventions used in this information........................................................................................................xvi

How to submit your comments................................................................................................................ xvii

Chapter 1. Notices................................................................................................. 1

Trademarks.................................................................................................................................................. 2

Homologation statement............................................................................................................................. 3

Safety and environmental notices............................................................................................................... 3

Safety notices and labels....................................................................................................................... 3

Special caution and safety notices...................................................................................................... 10

Environmental notices......................................................................................................................... 12

FCC certification................................................................................................................................... 12

Electromagnetic compatibility notices......................................................................................................12

Canada Notice...................................................................................................................................... 13

European Community and Morocco Notice......................................................................................... 13

Germany Notice....................................................................................................................................13

Japan Electronics and Information Technology Industries Association (JEITA) Notice....................14

Japan Voluntary Control Council for Interference (VCCI) Notice ...................................................... 14

Korea Notice......................................................................................................................................... 15

People's Republic of China Notice....................................................................................................... 15

Russia Notice........................................................................................................................................15

Taiwan Notice....................................................................................................................................... 15

United States Federal Communications Commission (FCC) Notice................................................... 16

Chapter 2. Technical overview............................................................................. 17

System overview........................................................................................................................................ 17

Drives..........................................................................................................................................................21

Drive slots............................................................................................................................................. 22

Power modules.......................................................................................................................................... 22

SSR access port......................................................................................................................................... 22

Hardware specification sheets.................................................................................................................. 23

EMS node specifications...................................................................................................................... 23

Chapter 3. Planning for hardware.........................................................................25

Planning for site preparation..................................................................................................................... 25

Site preparation and physical planning............................................................................................... 25

Planning for hardware installation............................................................................................................ 25

Planning for racks.................................................................................................................................25

Reviewing IBM Elastic Storage System 3200 location guidelines......................................................26

IBM Elastic Storage System 3200 model............................................................................................ 26

Planning for power for server canister.................................................................................................27

Physical installation planning....................................................................................................................29

iii

Содержание Elastic Storage System 3200





























































































































































Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды

IBM Elastic Storage System 3200, Руководство по планированию и установке оборудования

Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды