IBM Elastic Storage System 3200 Скачать руководство пользователя страница 32

Страница: 32 / 156

IBM Deutschland GmbH

Technical Relations Europe, Abteilung M456

IBM-Allee 1, 71139 Ehningen, Germany

Tel: +49 800 225 5426

e-mail: [email protected]

Generelle Informationen:
Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55032 Klasse A.

Japan Electronics and Information Technology Industries Association

(JEITA) Notice

This statement applies to products less than or equal to 20 A per phase.

This statement applies to products greater than 20 A, single phase.

This statement applies to products greater than 20 A per phase, three-phase.

Japan Voluntary Control Council for Interference (VCCI) Notice

14 IBM Elastic Storage System 3200: Hardware Planning and Installation Guide

Содержание Elastic Storage System 3200





























































































































































Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды

IBM Elastic Storage System 3200, Руководство по планированию и установке оборудования

Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды