IBM Elastic Storage System 3200 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 156

background image

Planning for 100 Gbps adapter

Review the pre-requisite system requirements and installation considerations before deployment.
It is helpful to be familiar with the following term when you are considering the features of the 100 Gbps

adapter for these connections.
Remote Direct Memory Access (RDMA)

RDMA is a networking standard that allows the adapters to transfer data directly to or from the

endpoints in a connection without using CPU resources on either of the endpoints. These transfers

occur simultaneously with other system operations and do not impact overall system performance.

When the system performs an I/O operation over an RDMA-based connection, data is sent directly to

the network, which reduces latency and increases the speed of data transfers.

Review the following elements when you are deciding to install the 100 Gbps adapters:
• The following adapters are available:

– AJZL: CX-6 InfiniBand/VPI in PCIe form factor

- InfiniBand - HDR200 200 Gb / HDR100 100 Gb / EDR 100 Gb
- Ethernet - 100 GbE

– AJZN: CX-6 DX in PCIe form factor (Ethernet - 100 GbE)

• Each canister has one port used for management functions and one additional port, the SSR service port

- mini USB serially connected, which is used by the SSR to check hardware and set the IP address.

Planning for cables

Connections for IBM Elastic Storage System 3200

Care must be taken to note the orientation of each server canister in IBM Elastic Storage System 3200 so

that the interconnect cables are properly connected.
IBM Elastic Storage System 3200 contains two server canisters. A label on IBM Elastic Storage System

3200 identifies each server canister and power module. In the following figure, server canister A/1 is on

the left side and server canister B/2 is on the right side.

A/1

A/1

B/2

B/2

Figure 16. Label showing the orientation of rear view of the server canisters and power modules

For example, the following figure shows the ports on IBM Elastic Storage System 3200.

Chapter 3. Planning for hardware 41

«
...
57
58
59
60
61
...
»

Содержание Elastic Storage System 3200





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Elastic Storage System 3200

Бренд: R/Evolution Страницы: 58

Бренд: JCAT Страницы: 3

Бренд: Euromate Страницы: 23

Бренд: Oracle Страницы: 312

2,5" EXTERNAL HARD DRIVE KIT

Бренд: Intenso Страницы: 94

totalstorage 200

Бренд: IBM Страницы: 180

Бренд: Icy Box Страницы: 36

Бренд: GARANT Страницы: 40

ValueLoader LTO-2

Бренд: Quantum Страницы: 94

Бренд: DataDirect Networks Страницы: 118

Бренд: Geekworm Страницы: 13

Бренд: morse Страницы: 4

Бренд: Synology Страницы: 31

Бренд: HP Страницы: 75

Бренд: Seagate Страницы: 32

Бренд: Fantom Drives Страницы: 10

Бренд: Fantom Drives Страницы: 160

Бренд: Hoggar Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды