IBM Elastic Storage System 3200 Скачать руководство пользователя страница 71

Страница: 71 / 156

Figure 30. Securing the rail

d) Repeat the installation steps of inner rail on right side of the enclosure to secure the other inner rail

on left side of the enclosure.

Installing enclosures (IBM SSR task)

Following your enclosure location plan, install the IBM Elastic Storage System 3200 system.

CAUTION:
• To lift an IBM Elastic Storage System 3200 system requires at least two people. To reduce the

enclosure weight to permit one person to safely lift the enclosure, you must temporarily remove

the server canisters, power modules, and all drives from the enclosure.

• Install an IBM Elastic Storage System 3200 system only onto the IBM Elastic Storage System

3200 system rails supplied with the enclosure.

• Load the rack from the bottom up to ensure rack stability. Empty the rack from the top down.

To install an enclosure, complete the following steps:

1. Align the enclosure both horizontally and square to the rails, while facing the front of the IBM Elastic

Storage System 3200 as shown in the following figure.

Click

Figure 31. Alignment of the enclosure

2. Ensure that the ball bearing retainers are at the front of the left and right cabinet member rails. This is

followed by an audible click.

3. Insert each inner rail into the rack cabinet as shown in the following figure.

Chapter 4. Installing 53

Содержание Elastic Storage System 3200





























































































































































Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды

IBM Elastic Storage System 3200, Руководство по планированию и установке оборудования

Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды