IBM Elastic Storage System 3200 Скачать руководство пользователя страница 70

Страница: 70 / 156

Figure 27. Securing the front of the rails

7. Repeat the installation steps of left outer rail to install the right outer rail on the rack post.
8. Install the inner rail on the right side of the enclosure as follows:

a) Align the large section of the keyholes on the right inner rail with the standoffs on the right side of

the chassis. See the following figure.

Front

Rear

Figure 28. Standoffs aligned with the keyholes

b) Slide the rail toward the back of the enclosure to secure the standoff on the smaller section of the

keyhole to lock the rail in place, which is accompanied by an audible click. See the following figure.

Figure 29. Standoffs secured over the keyholes

c) Secure the rail in place by using one of the M4 screws in the hole just behind the release tab. See

the following figure.

52 IBM Elastic Storage System 3200: Hardware Planning and Installation Guide

Содержание Elastic Storage System 3200





























































































































































Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды

IBM Elastic Storage System 3200, Руководство по планированию и установке оборудования

Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды