IBM Elastic Storage System 3200 Скачать руководство пользователя страница 35

Страница: 35 / 156

Chapter 2. Technical overview

The technical overview topics provide information about the key concepts of IBM Elastic Storage System

3200.
Target audience of this chapter: Customers and IBM Service Support Representative (SSR).

System overview

An IBM Elastic Storage System 3200 enclosure contains Non-Volatile Memory Express (NVMe) attached

SSD drives and a pair of server canisters.
IBM Elastic Storage System 3200 is an all-Flash array platform. This storage platform uses NVMe-

attached SSD drives to provide significant performance improvements as compared to SAS-attached flash

drives.
IBM Elastic Storage System 3200 can contain up to 24 NVMe-attached SSD drives. You can either use 12

drives in a half-populated configuration or 24 drives in a fully populated configuration. These drives are

accessible from the front of IBM Elastic Storage System 3200, as shown in the following figure.
Note: The minimum number of drives is 12. In a 12-drive configuration, drives must be plugged into slots

1 - 6 and then 13 - 18.

Figure 1. Front view of IBM Elastic Storage System 3200

Each IBM Elastic Storage System 3200 contains two identical I/O server canisters. The following figure

shows two I/O server canisters and two power modules.

Figure 2. Rear view of IBM Elastic Storage System 3200

The IBM Elastic Storage System 3200 system uses a single socket AMD EPYC Rome processor per I/O

canister node. The following table provides an overview of IBM Elastic Storage System 3200.

Содержание Elastic Storage System 3200





























































































































































Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды

IBM Elastic Storage System 3200, Руководство по планированию и установке оборудования

Результаты поиска

Содержание Elastic Storage System 3200

Отзывы:

Похожие инструкции для Elastic Storage System 3200

Бренды по названию

Популярные бренды