IBM 9080-M9S страница 94 Скачать руководство пользователя

Страница: 94 / 730

4. Determine whether the repair operation can continue when the system power is turned on.

To continue the repair operation when the system power is turned on, the following conditions must

be true:
• Fans must be installed in all three slots.

Each of the three fans has a green LED and an amber LED, as shown in Figure 75 on page 88. The

green LED is lit solid for all fans, but the fan with the failure has a flashing amber fault LED.

• If only one amber fault LED is On, the repair operation can be completed when the system power is

turned on.

Figure 75. Fan LEDs in the system control unit

5. Ensure that the amber LED corresponds to the location of the fan with the lit fault LED.
6. If you can complete the procedure with the system power turned on, continue with step “8” on page

88.

7. If you powered off the system earlier in this procedure or you want to power off the system to

complete the repair operation, complete the following steps:

a) If the system is powered off, continue with step “7.b” on page 88. Otherwise, prepare to power

off the system.

Attention: Ensure that you shut down the running logical partitions on the managed system

before you power off the managed system. Powering off the managed system without

shutting down the logical partitions first causes the logical partitions to shut down

abnormally and can cause data loss. If you use a Virtual I/O Server (VIOS) logical partition,

ensure that all clients are shut down or that the clients have access to their devices by using

an alternative method.

When you are ready to power off the system, from the Operation list, select System Level

Deactivate. Then, click OK to confirm the operation.

b) From the Operation list, select FRU Level Deactivate. Then, click OK to confirm the operation.

c) Stop the system. For instructions, see Stopping a system (www.ibm.com/support/

knowledgecenter/POWER9/p9haj/crustopsys.htm).

8. Attach the electrostatic discharge (ESD) wrist strap.

The ESD wrist strap must be connected to an unpainted metal surface until the service procedure is

completed, and if applicable, until the service access cover is replaced.

Attention:

88 Power Systems: Removing and replacing parts in the 9080-M9S system

Содержание 9080-M9S



























































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 9080-M9S

Отзывы:

Похожие инструкции для 9080-M9S

Бренды по названию

Популярные бренды

IBM 9080-M9S, Руководство пользователя

Результаты поиска

Содержание 9080-M9S

Отзывы:

Похожие инструкции для 9080-M9S

Бренды по названию

Популярные бренды