IBM 9080-M9S Скачать руководство пользователя

Страница: 17 / 730

Figure 10. Connecting the rear power cords

Preparing the system for operation after removing and replacing a line cord conduit from

the 9080-M9S system node

To prepare the system for operation after removing and replacing a line cord conduit, complete the steps

in this procedure.

Procedure
If the customer required the system to be powered off to complete the repair, have the customer perform

the following steps. If the customer did not require the system to be powered off, no additional steps are

necessary.

a) To power on the system, from the Operation list, select System Level Activate. Then, click OK to

confirm the operation.

b) To restart the logical partitions, complete the following steps:

1) In the navigation area, click the Resources icon

, and then click All Systems.

2) Click the system name in which you want to activate the logical partition.
3) Select the logical partition name that you want to activate.

Cables 11

Содержание 9080-M9S



























































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 9080-M9S

Отзывы:

Похожие инструкции для 9080-M9S

Бренды по названию

Популярные бренды

IBM 9080-M9S, Руководство пользователя

Результаты поиска

Содержание 9080-M9S

Отзывы:

Похожие инструкции для 9080-M9S

Бренды по названию

Популярные бренды