IBM 9080-M9S Скачать руководство пользователя

Страница: 52 / 730

Figure 38. Identify LEDs for the UPIC cables on the system control unit

5. Attach the electrostatic discharge (ESD) wrist strap.

The ESD wrist strap must be connected to an unpainted metal surface until the service procedure is

completed, and if applicable, until the service access cover is replaced.

Attention:
• Attach an electrostatic discharge (ESD) wrist strap to the front ESD jack, to the rear ESD jack,

or to an unpainted metal surface of your hardware to prevent the electrostatic discharge from

damaging your hardware.

• When you use an ESD wrist strap, follow all electrical safety procedures. An ESD wrist strap is

used for static control. It does not increase or decrease your risk of receiving electric shock

when using or working on electrical equipment.

• If you do not have an ESD wrist strap, just prior to removing the product from ESD packaging

and installing or replacing hardware, touch an unpainted metal surface of the system for a

minimum of 5 seconds. If at any point in this service process you move away from the

system, it is important to again discharge yourself by touching an unpainted metal surface for

at least 5 seconds before you continue with the service process.

46 Power Systems: Removing and replacing parts in the 9080-M9S system

Содержание 9080-M9S



























































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 9080-M9S

Отзывы:

Похожие инструкции для 9080-M9S

Бренды по названию

Популярные бренды

IBM 9080-M9S, Руководство пользователя

Результаты поиска

Содержание 9080-M9S

Отзывы:

Похожие инструкции для 9080-M9S

Бренды по названию

Популярные бренды