IBM 9080-M9S Скачать руководство пользователя | Manualshive

Страница: 721 / 730

background image

Preparing the 9080-M9S system for operation after permanently removing the USB card

To prepare the system for operation after permanently removing the USB card, complete the steps in this

procedure.

Procedure

1. Ensure that you have the electrostatic discharge (ESD) wrist strap on and that the ESD clip is plugged

into a ground jack or connected to an unpainted metal surface. If not, do so now.

2. To complete the procedure with the power on, access the ASMI and run the Cable Plugging Validation

utility to validate only the UPIC cables.

a) If you are already connected to the ASMI, go to the next step. Otherwise, click All Systems then

select system being serviced. Then, click Actions > View All Actions > Launch Advanced

Systems Management (ASM).

b) In the navigation area, expand System Service Aids > Cable Plugging Validation. Then, click

Validate UPIC Cables. The system verifies that the UPIC cables are present.
Note: Older firmware levels do not support validating the UPIC cables while the system is at FSP

standby. You can skip this step if it is not available.

c) Expand System Service Aids > Cable Plugging Validation. In the Display Cable Status section,

select UPIC Cables and click Continue. The system validates that the UPIC cables are installed in

the correct locations and displays a table with the results. Ensure that the plugging status is OK for

each cable in the displayed table. If the status is OK, no further action is required. If the status is

not OK, review the error logs, correct the problems, and repeat steps b and c as needed until the

status is OK for all cables.

d) Exit the ASMI.

e) Continue with step #unique_133/unique_133_Connect_42_step_activate_partitions.

3. If you chose to complete this repair with the power off, using your labels, reconnect the UPIC cables to

the system control unit.
UPIC cable locations are P1-C1-T1 and P1-C2-T1.

a. Ensure that the white plastic lock is pulled back from the plug housing.

b. Plug the UPIC cable (A) into the previously identified location in the system control unit by inserting

the cable into the connector until it locks into place.

Figure 627. Replacing the UPIC cable into the system control unit

USB card 715

«
...
719
720
721
722
723
...
»

Содержание 9080-M9S



























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 9080-M9S

Бренд: Xaoc Devices Страницы: 8

FrameSaver 9620

Бренд: Paradyne Страницы: 4

Бренд: Wayne Страницы: 8

Бренд: Performance Tool Страницы: 6

Бренд: Robust Страницы: 44

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Бренд: YATO Страницы: 80

Бренд: Stanley Страницы: 10

Бренд: Campbell Hausfeld Страницы: 48

Бренд: Elenco Electronics Страницы: 8

Бренд: Ingersoll-Rand Страницы: 52

Бренд: Scheppach Страницы: 72

Бренд: Fisher Scientific Страницы: 20

Бренд: H3C Страницы: 16

Бренд: Hakko Electronics Страницы: 2

Бренд: STEINEL PROFESSIONAL Страницы: 10

Super wood shaper

Бренд: Wolfcraft Страницы: 32

Бренд: Darex Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды