IBM 9080-M9S Скачать руководство пользователя | Manualshive

Страница: 423 / 730

background image

d. Lightly pull on the UPIC cable from both attachment points to ensure it is locked into place. Pull the

cable connector; do not pull on the wire. The cables should be firmly attached to the system.

6. When the service processor comes up to the Flexible Service Processor (FSP) standby state (the

power-on LED on the control panel is flashing slowly), continue to the next step.

7. Access the ASMI and run the Cable Plugging Validation utility to validate all of the cables.

a) If you are already connected to the ASMI, go to the next step. Otherwise, click All Systems then

select system being serviced. Then, click Actions > View All Actions > Launch Advanced

Systems Management (ASM).

b) In the navigation area, expand System Service Aids > Cable Plugging Validation. Then, click

Validate Cables. The system verifies that the expected cables are present.

c) If your configuration includes two or more nodes, expand System Service Aids > Cable Plugging

Validation. Then, click Verify Node Position. Otherwise, if your configuration includes only one

node, continue to the next step.
If the system is cabled correctly, the blue identify LED on each system node will light up, in

sequence, from the top node to the bottom node. If the LEDs do not light up in sequence, the FSP

cables need to be re-installed.

d) Expand System Service Aids > Cable Plugging Validation. Then, select All of the above in the

Display Cable Status section and click Continue. The system validates that the cables are installed

in the correct locations. Expand System Service Aids > Cable Plugging Validation to display a

table with the results. Ensure that the plugging status is OK for each cable in the displayed table. If

the status is OK, no further action is required. If the status is not OK, review the error logs, correct

the problems, and repeat steps b, c and d as needed until the status is OK for all cables.

e) Exit the ASMI.

Permanently removing

Preparing the 9080-M9S system to permanently remove an NVMe U.2 drive

To prepare the system to permanently remove an NVMe U.2 drive, complete the steps in this procedure.

Procedure

1. If applicable, open the rack door at the rear of the system.
2. Review the NVMe U.2 drive slot locations. The NVMe U.2 drive slots are located in the rear of the

system.

NVMe drives 417

«
...
421
422
423
424
425
...
»

Содержание 9080-M9S



























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 9080-M9S

Бренд: Fein Страницы: 148

Бренд: Gage Bilt Страницы: 9

Бренд: Gage Bilt Страницы: 13

Бренд: National Instruments Страницы: 8

FrameSaver 9620

Бренд: Paradyne Страницы: 4

Бренд: M-system Страницы: 3

Бренд: Ransburg Страницы: 40

Бренд: H3C Страницы: 5

Бренд: kincrome Страницы: 12

Бренд: Master Appliance Страницы: 2

2000-2 LNB Series

Бренд: Cross Technologies Страницы: 8

Бренд: Far Tools Страницы: 17

Бренд: X-FLOC Страницы: 51

Бренд: Baileigh Industrial Страницы: 44

Бренд: F.F. Group Страницы: 60

Бренд: Cornwell Tools Страницы: 4

Бренд: Cutech Страницы: 40

Бренд: Agilent Technologies Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды