IBM 9080-M9S страница 655 Скачать руководство пользователя

Страница: 655 / 730

Figure 569. Locking the system processor module into the tool

5. Hold the outside of the tool and lift the tool and system processor module from the socket.

Lift the tool upward slowly to ensure that the jaws are fully engaged with the system processor

module. Ensure that the system processor module does not disengage and fall back into the socket of

the system processor module. If the system processor module falls back into the socket of system

processor module, the pins may be damaged.
Place the system processor module at an angle on the top cover of the packaging as shown in Figure

570 on page 650. Setting the tool and system processor module at an angle on the top cover of the

system processor module packaging makes it easier to place the system processor module in the

packaging.

System processor module 649

Содержание 9080-M9S



























































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 9080-M9S

Отзывы:

Похожие инструкции для 9080-M9S

Бренды по названию

Популярные бренды

IBM 9080-M9S, Руководство пользователя

Результаты поиска

Содержание 9080-M9S

Отзывы:

Похожие инструкции для 9080-M9S

Бренды по названию

Популярные бренды