IBM 3746-900 Скачать руководство пользователя страница 213

Страница: 213 / 276

Removal the 3746-900 attached to a 3745-X1A

Step

4. ____ Unplug the 3746-900 main power cable, or ask the customer to dis-

connect the 3746-900 power cable from its ac power receptacle (or dc
power if any).

Note: If you have to remove a controller expansion, you have to discon-
nect its power cable following the same procedures.

Step

5. ____ Coil the disconnected power cable inside the 3746-900.

Disconnecting the Interface Cables

Step

1. ____ If the machines are being relocated, label and remove all data set

cables from the TRA and ESCA adapters.

Note: It is advisable to disconnect the cables, starting at the top of the
gate (expansion board 07M-A1), and working down.

Step

2. ____ Remove the cable (PN 76F9440 or 76F9441) from the 8228 LAN

adapter (plugs 1 to 8) to the 3746-900 01N-A1 F1.

Disconnecting Inter-Machine Cabling

Step

1. ____ Proceed in reverse order, as for the installation (see Chapter 4,

“Connecting the 3746-900 to a 3745-X1A” on page 4-1), and disconnect
the following inter-machine cables:

a. ____ Power control cable (PN 03F7538) from the 3745, and then coil

it up.

b. ____ UEPO cable (PN 76F9341) from the 3745.

c. ____ +5V cables, if they exist (two for PN 76F9338 and two for PN

76F9339), from the 3745 or 3746 frames.

d. ____ IOC and DMA bus flat cables. Roll and secure them in the

3746-900 frame.

Step

2. In the 3745 or 3746 boards:

a. ____ Where the IOC and DMA cables have been removed, remove

the dico cards (PN 17G6080) then plug the LA bus terminator cards
into the same locations.

b. ____ Using the function 'Locate Bypass Card Position', locate the

active and passive bypass cards (PN 09G2862, 09G2864, and
6264604). Remove these cards and put them in the 3746-900 ship-
ping group.

Step

3. ____ Remove the frame-to-frame screws (PN 1621596) and spacers (PN

72F0659) see Figure 4-1 on page 4-3. Put these parts into an envelope.
Write the part number on the envelope, and place it in the shipping group.

Chapter 12. Removal or Relocation of the 3746-900 Attached to a 3745-X1A

12-3

Содержание 3746-900





















































































































































































































































































Результаты поиска

Содержание 3746-900

Отзывы:

Похожие инструкции для 3746-900

Бренды по названию

Популярные бренды

IBM 3746-900, Руководство по установке

Результаты поиска

Содержание 3746-900

Отзывы:

Похожие инструкции для 3746-900

Бренды по названию

Популярные бренды