IBM 3746-900 Скачать руководство пользователя страница 214

Страница: 214 / 276

Removal the 3746-900 attached to a 3745-X1A

Preparing Machines for Shipment

Step

1. ____ Remove the end cover on the right side. Loosen the four retaining

screws using a 5/16" socket from inside the machine. Then lift the cover
from the slotted holes on the frame and pull it towards you.

Step

2. ____ Re-install the end cover at the right side of the 3745 base frame,

3746-A11, or 3746-A12, depending on the 3745 configuration.

Step

3. ____ Re-install all parts removed from frames, covers, and doors.

Step

4. ____ Re-install the shipment bars on the upper and lower ends of the

basic board (and expansion board if any, see Figure 2-2 on page 2-3)

Step

5. ____ Pack the machine using the pack/unpack instructions.

Step

6. ____ Pack the customer's parts and documentation in one package and

label it: "Customer Package".

Step

7. ____ Pack other parts and all maintenance documentation in another

package and label it: "Maintenance Package". Hold for use by IBM
Service Representative.

Step

8. ____ Coil all removed cables and store them alongside the machine.

Step

9. ____ Complete the removal records according to existing procedures.

Inform the IBM Branch Office that the machines are ready for shipment.

Testing the 3745

Step

1. ____ Run CDF verify (see step 2 on page 5-2 for details).

Step

2. ____ Run the IOC and DMA diagnostics (see step 5 on page 5-5 for

details).

Step

3. ____ Ask the customer to re-start and check the network.

12-4

3746-900: Installation Guide

Содержание 3746-900





















































































































































































































































































Результаты поиска

Содержание 3746-900

Отзывы:

Бренды по названию

Популярные бренды

IBM 3746-900, Руководство по установке

Результаты поиска

Содержание 3746-900

Отзывы:

Бренды по названию

Популярные бренды