Hytera TETRA PT580H F5 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 33

Hytera TETRA PT580H F5 Скачать руководство пользователя страница 18

Owner’s Manual

Status Indication

5. Status Indication

5.1

Status Icon

Name

Icon

Indication

Battery Strength Icon

The battery is low.

More bars indicate better battery strength.

RSSI Icon

The terminal has not registered with the network

(applicable for TMO only).

More bars indicate better signal strength.

Message Icon

Unread

message(s).

The Inbox is full.

Operation Mode Icon

The terminal is operating in TMO.

The terminal is operating in DMO.

The terminal is operating in fall-back mode.

Profile Icon

Silent

Normal

Vibration

Accessory Icon

The audio accessory is connected.

GPS Icon

A GPS module is connected and the valid GPS data is

received.

Valid GPS data can be received, and the audio

accessory has been connected.

A GPS module is connected and no valid GPS data is

received.

No valid GPS data can be received, and the audio

accessory has been connected.

Call Icon

A call is in progress.

«
...
16
17
18
19
20
...
»

Содержание TETRA PT580H F5


































Отзывы:

Нет отзывов