Hypertherm Echion Скачать руководство пользователя страница 87

Страница: 87 / 194

Preventive maintenance

Echion

Operator

Manual 810770

even

tive maint

enance

Disconnect the lower ends of the hydraulic hoses that enter the top of the tank.

Remove the filter element and install a new element. Refer to

Replace the hydraulic filter

element

on page 84 for instructions.

Disassemble the hydraulic tank cover.

Disconnect the temperature/level sensor cable.

Disconnect the hydraulic hose from the filter.

Remove the 2 hoses that pass through the cover.

Use a 7/16-inch open-ended wrench to remove the bolts and washers (10 each) from the
tank cover.

Clean the inner surfaces of the tank with clean towels. Make sure that no debris is left in the
bottom of the tank.

Assemble the hydraulic tank cover.

Install the tank cover bolts and washers (10 each).

Install the 2 hoses that pass through the cover.

Connect the hydraulic hose from the filter

Connect the temperature/level sensor cable.

Fill the tank with hydraulic fluid until the fluid is at the top mark on the sight gauge.

10.

Install a new filler cap.

11.

Discard the used parts.

12.

Turn

the pump in pierce-pressure mode.

13.

Monitor for leaks.

14.

Add hydraulic fluid, if necessary. Refer to

Add hydraulic fluid

on page 85.

15.

Operate the pump in pierce-pressure mode for 15 to 20 minutes.



If air is in the hydraulic system, the pump can be noisy during operation. Refer to

The

pump makes noise during operation

on page 133.

CAUTION

Remove all towels from the tank before putting hydraulic fluid in it.

CAUTION

Do not use soap, detergent, or solvents. Isopropyl alcohol can be used to clean the
tank.

Содержание Echion



































































































































































































Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды

Hypertherm Echion, Руководство оператора

Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды