Hypertherm Echion Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 194

background image

Installation

7

Echion

Operator

Manual 810770

163

Ins

ta

lla

ti

on

Flush the pump and the high-pressure tubing

It is common for small pieces of metal and debris to be present in newly installed high-pressure
tubing. Flush the system to prevent damage to orifices, on/off valve parts, and other components of
the high-pressure system.

1.

Remove the cutting head and the orifice.

2.

Make sure that the on/off valve is closed.

3.

Turn

ON

the pump.

4.

Set the pressure to 345 bar (5,000 psi).

5.

On the operator interface, touch the

symbol to start the pump.

6.

Make a program that turns the valve

ON

and

OFF

in 1-second increments. Operate the program

in a loop for 15 minutes.

If a program is not available, turn the cutting head

ON

and

OFF

in 1-second intervals

for 15 minutes. This loosens debris in the high-pressure tubing.

7.

Turn

OFF

the pump.

8.

Install a ruby orifice in the cutting head. For orifice sizes, refer to

9.

Turn

ON

the pump.

10.

On the operator interface, touch the

symbol to start the pump.

11.

Increase the pressure to 2,760 bar (40,000 psi). Operate the program in a loop for 15 minutes.

12.

Increase the pressure to 4,140 bar (60,000 psi). Operate the program in a loop for 15 minutes.

If the on/off valve leaks, examine the needle, the seat, the seals, and the orifice for damage.
Replace parts, if necessary.

The pump is ready for normal operation.

CAUTION

This procedure can cause damage to the on/off valve needle and the seat and to the orifice.

Keep spare parts and orifices available.

If this pump was purchased through an OEM, the OEM could recommend a different procedure
to flush out the high-pressure tubing.

«
...
161
162
163
164
165
...
»

Содержание Echion



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Echion

Бренд: Danfoss Страницы: 72

Бренд: Watson Marlow Pumps Страницы: 131

Бренд: Eaton Страницы: 57

Бренд: A.O. Smith Страницы: 2

Бренд: A.O. Smith Страницы: 2

Zoneline AZ85H09DAC

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: Davey Страницы: 16

Бренд: YUKEN KOGYO Страницы: 82

Бренд: Carrier Страницы: 30

Бренд: Rotex Страницы: 80

Бренд: Flo Fab Страницы: 9

Бренд: Daewoo Страницы: 16

Бренд: Xylem Страницы: 20

Бренд: Ozito Страницы: 6

Бренд: SAMES KREMLIN Страницы: 50

Бренд: Nortek Страницы: 16

Бренд: Textron Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды