Hypertherm Echion Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 194

background image

Safety

SC-26

810770 Operator

Manual

Echion

Sa
fe

ty

WARNING

A person who works on deenergized machinery can be injured or killed if the machinery is
energized without permission.

All personnel in an area where energy-control procedures are used must receive training for
energy-control procedures.

WARNING

DANGEROUS VOLTAGE/RISK OF SHOCK

Doing work on this equipment while it is energized is dangerous.

Personnel who maintain and repair this equipment can be injured or killed if dangerous energy is
not controlled.

Injuries can include burns, cuts, fractures, or electrocution.

WARNING

Before removing a lock-out device:



obey the employer’s energy-control procedure.



examine machines and parts to make sure that they are operational.



make sure that all personnel are safely away from machines.

After removing energy-isolation devices, make sure that all personnel in the area know that the
devices are removed and that the machine is being energized.

WARNING

To reduce the risk of injuries or death, wear approved protection and obey safety
recommendations when doing work with electricity.

WARNING

When work must be done in a small space or an area with limited access, the access must not
be blocked by ventilation ducts, hoses, pipes, or other equipment.

WARNING

Do not block or remove warnings, cautions, or instructions.

WARNING

Personal protective equipment is recommended.

If you do not use personal protective equipment, there is a risk of injury or death.

WARNING

High-pressure water can cause eye injuries.

Wear approved eye protection when operating or doing work near this equipment.

WARNING

This waterjet equipment could make more noise than is permitted by national or local codes.

When this intensifier is operating, the noise level is 75 dB(A) to 85 dB(A).

Water flow rate, pipe layout, and the acoustical characteristics of the building have an effect on
noise level.

Long periods of exposure to noise can cause permanent hearing loss.

Wear approved ear protection and control exposure time when operating or doing work near this
equipment.

«
...
24
25
26
27
28
...
»

Содержание Echion



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Echion

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 8

Бренд: Zehnder Rittling Страницы: 64

Бренд: vacuubrand Страницы: 44

Бренд: DAB Страницы: 184

Бренд: DAB Страницы: 184

Бренд: York Страницы: 204

Бренд: GEA Страницы: 337

Бренд: AromaMist Страницы: 15

HOT Splash HS40

Бренд: Duratech Страницы: 36

Бренд: Elkay Страницы: 2

Бренд: Daikin Страницы: 44

Cascademax Series

Бренд: ubbink Страницы: 54

DIO 45/13 fl ex

Бренд: T.I.P. Страницы: 52

MiniTank WM-1.0

Бренд: Waiwela Страницы: 20

Бренд: Utilitech Страницы: 40

Бренд: Panduit Страницы: 7

Бренд: Texas Equipment Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды