Hypertherm Echion Скачать руководство пользователя страница 84

Страница: 84 / 194

Preventive maintenance

810770 Operator

Manual

Echion

Pr
ev
entive main

tenance

Replace the hydraulic filter element

Parts, tools, and materials

Do this task when the pump is not operating.

Remove the top cover and the front panel. Refer to

Inspect the pump

on page 39.

Remove the used filter element from the filter head.



Use a 15/16-inch crowfoot wrench or a socket if the filter element is too tight to
remove by hand.

Put clean hydraulic fluid on the gasket of the new filter element.

Twist the filter element into the filter head.

Use a torque wrench to tighten the filter to a value between 13.5 N ∙ m (10 lbf ∙ ft)
and 16 N ∙ m (12 lbf ∙ ft).

Turn

the pump in pierce-pressure mode.

Look at the sight gauge to check the hydraulic fluid level. Add hydraulic fluid, if necessary.

Do this task:



every 1,500 hours.



when the needle on the hydraulic gauge is in the red zone while the pump is at stable temperature.

Filter head

Sight gauge

Hydraulic filter element

Antiwear (AW) mineral oil or synthetic hydraulic
fluid, ISO viscosity grade (VG) 32 or 46

Torque wrench

15/16-inch crowfoot wrench or socket

Recommended materials

Clean funnel

Clean towels

Содержание Echion



































































































































































































Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды

Hypertherm Echion, Руководство оператора

Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды