Hypertherm Echion Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 194

background image

Troubleshooting

5

128

810770 Operator

Manual

Echion

T

ro

ubl

es
hoo

ti

ng

Water

Low-pressure water

The supply-water pressure is too low.

A pressure switch before the water filter senses the supply-water pressure. If the value on the
prefilter water-pressure gauge is lower than 2.8 bar (280 kPa / 40 psi), the water pressure to the
intensifier is too low. This causes a fault.

The supply-water pressure or flow is not sufficient.

Make sure that the supply water meets requirements found in

The supply-water pressure is too high.

If the value on the prefilter water-pressure gauge is higher than 7.6 bar (760 kPa / 110 psi), the
water pressure is too high.

The boost pump is not needed.

The low-pressure water parts are rated for a maximum pressure of 8.6 bar (860 kPa / 125 psi).

In environments with high supply-water pressure, the boost pump can increase the water
pressure to higher than the maximum. This can cause damage to the water filter and other parts.

If the value on the prefilter water–pressure gauge is higher than 4.8 bar (480 kPa / 70 psi):



In the electrical enclosure, turn the switch on the boost pump motor contactor to

0

.



On the operator interface, turn

OFF

boost pump monitoring. Refer to

The boost pump bypass relief valve is not adjusted correctly.

Adjust the boost pump pressure

on page 162 for instructions for adjusting the valve.

«
...
126
127
128
129
130
...
»

Содержание Echion



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Echion

Delta Solo Compact MVP Series

Бренд: KSB Страницы: 40

Бренд: T.I.P. Страницы: 136

Бренд: Endress Страницы: 17

Бренд: Gorenje Tiki Страницы: 48

Milton Roy Milroyal Series

Бренд: Accudyne Industries Страницы: 68

Бренд: Raypak Страницы: 41

Hydro-Guard HG-4

Бренд: Mueller Страницы: 8

Бренд: Giant Страницы: 12

Бренд: Simer Страницы: 24

Бренд: Launtop Страницы: 22

Бренд: XtremepowerUS Страницы: 14

Бренд: VAC-CON Страницы: 16

Бренд: Bock Water heaters Страницы: 60

Бренд: Kohler Страницы: 24

Бренд: SKAMET Страницы: 3

HAWK LEUCO TXT Series

Бренд: Kärcher Страницы: 36

Бренд: Grundfos Страницы: 60

Бренд: Waldbeck Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды