Hypertherm Echion Скачать руководство пользователя страница 159

Страница: 159 / 194

Installation

Echion

Operator

Manual 810770

159

Ins

lla

Check the hydraulic fluid

Look at the sight gauge to check the hydraulic fluid level. Add hydraulic fluid, if necessary. Refer to

Add hydraulic fluid

on page 85 for instructions.

Do the first start

Use this procedure:



at installation.



when putting the equipment into operation after storage or shipping.



after maintenance or repairs are done on the intensifier, the high-pressure water system, or
the low-pressure water system.

CAUTION

Make sure that hydraulic fluid is available during installation and for the first start.

CAUTION

If a water line, a fitting, or a valve could be frozen, do not operate the pump. Thaw the equipment
until water moves easily through the system.

Examine the parts for damage. Replace parts, if necessary.

CAUTION

This procedure could cause damage to the orifice.

Do not do the first start with a diamond orifice installed. Hypertherm recommends using a ruby
orifice during the first 40 hours of operation.

Содержание Echion



































































































































































































Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды

Hypertherm Echion, Руководство оператора

Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды