Hypertherm Echion Скачать руководство пользователя страница 156

Страница: 156 / 194

Installation

156

810770 Operator

Manual

Echion

Inst

alla

Connect the utilities to the pump

The utility connections are identified with hang tags. The tags have symbols on them that
correspond with the table on

page 157

Remove the top cover and the front panel. Refer to

Inspect the pump

on page 41 for

instructions.

Remove the caps from the fittings and the plugs from the utility connections.

CAUTION

Compressed air is an energy source that can eject with force.

Be careful when connecting to and disconnecting from this energy source.

CAUTION

WATER-COOLED SYSTEM

Do not connect the

Waste water out

hose and the

Cooling out

line together.

Connecting these hoses can cause cooling water to back up into the system, which can cause
damage to the bleed-down valve and intensifier parts.

CAUTION

To prevent dirty water from entering the bleed-down valve, install the

Waste water out

hose so

that it is below the bleed-down valve.

Refer to

Fittings

on page 144 for torque values and information about how to correctly install

high-pressure water fittings.

Parts, tools, and materials

9/16-inch open-ended wrench

1/8-inch NPT male fitting

13/16-inch open-ended wrench

3/8-inch high-pressure male fitting

1-1/16-inch open-ended wrench

Two 1/2-inch NPT male fittings

Torque wrench

High-pressure antiseize lubricant such as Blue Goop or PURE Goop

Water-cooled system

1-inch open-ended wrench

Two 1/2-inch NPT male fittings

1-3/16-inch open-ended wrench

Keep the caps and the plugs to use if the pump is stored or shipped.

Содержание Echion



































































































































































































Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды

Hypertherm Echion, Руководство оператора

Результаты поиска

Содержание Echion

Отзывы:

Похожие инструкции для Echion

Бренды по названию

Популярные бренды