Hydro-Gear 310-1500 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 48

background image

-1500/-1700 IHT

13

RETURN TO NEUTRAL SETTING
FOOT CONTROL

WARNING

POTENTIAL FOR SERIOUS IN JU RY

Certain procedures re quire the vehicle
en gine to be operated and the vehicle to
be raised off of the ground. To pre vent
pos si ble injury to the ser vic ing tech-
ni cian and/or by stand ers, in sure the
ve hi cle is prop er ly se cured.

The return to neutral mechanism on the trans-
mis sion is designed to set the di rec tion al con-
trol into a neutral po si tion when the operator
re moves their foot from the foot control. Fol low
the pro ce dures below to prop er ly adjust the
return to neu tral mech a nism on the transaxle:

1. Con

fi

rm the transaxle is in the operating

mode (bypass disengaged). Raise the
ve hi cle’s drive tires off the ground to allow
free ro ta tion.

NOTE: It may be necessary to remove
the drive tire from the axle hub to ac cess
the linkage control and the transaxle
con trol arm.

2. Remove the Original Equipment Man u fac -

tur er’s (OEM’s) control linkage at the control
arm. Refer to Figure 9.

WARNING

Do not attempt any adjustments with the
engine running. Use extreme caution
while inspecting all vehicle linkage!

Follow all safety procedures outlined in
the vehicle owner’s manual!

3. Start the engine and increase the throttle to

full engine rpm.

4. Check for axle rotation. If the axles do not

ro tate, go to Step 5. If the axles rotate, go
to Step 6.

5. Stop the vehicle’s engine. Adjust the OEM

linkage according to the OEM manual. Re-
check according to Step 3 and 4. Stop the
ve hi cle engine. Refer to Figure 9.

6. Note the axle directional movement . Stop

the vehicle engine. Loosen the adjusting
puck screw until the puck can be rotated.
Rotate the adjusting puck the opposite di-
rection of the wheel rotation on the control
linkage side in 5 degree increments. Tighten
the ad just ing puck screw. Refer to Table 5.
Required Torque Values, Page 17. Recheck
ac cord ing to Step 3 and 4. Stop the vehicle
engine. Ad just the OEM linkage according
to the OEM man u al. Re check according to
Step 3 and 4. Re fer to Fig ure 9.

Figure 9. Return to Neutral, Foot Control

«
...
13
14
15
16
17
...
»

Содержание 310-1500

















































Отзывы:

Нет отзывов

Похожие инструкции для 310-1500

Бренд: Minarik Страницы: 2

Бренд: Teac Страницы: 15

Бренд: Eaton Страницы: 14

Super-Writemaster SH-S223Q

Бренд: Samsung Страницы: 2

SH-S203B - WriteMaster - DVD±RW

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 5

Бренд: Samsung Страницы: 6

Бренд: Shugart Страницы: 32

Бренд: Shugart Страницы: 80

M2 500N/EV1/RWA Series

Бренд: STG-BEIKIRCH Страницы: 8

Бренд: LinMot Страницы: 29

Бренд: Eurotherm Drives Страницы: 203

Бренд: Stanley Страницы: 20

Бренд: ABB Страницы: 28

ACH580-01 Series

Бренд: ABB Страницы: 396

Бренд: ABB Страницы: 24

Бренд: Xinje Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды