Hydro-Gear 310-1500 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 48

background image

22

-1500/-1700 IHT

SEAL KIT REPLACEMENT

Before disassembly, wipe the unit free of any
debris to avoid contamination.

Refer to Fig ure 16.

INPUT SEAL

1. Remove the input pulley from the input

shaft.

2. Remove the seal retaining ring (7).

3. Carefully pull the input seal (5) out of the

housing bore with a “hook” type tool. Care
must be taken to avoid damage to the hous-
ing bore or shaft sealing area.

4. Lubricate the new seal with petroleum jelly

prior to installation.

5. Wrap the shaft keyway (splines) with cel-

lo phane to prevent damage to the seal lip
dur ing installation.

6. Slide the seal over the shaft and press it into

the housing bore.

7. The seal should seat against the spacer.

8. Install the seal retaining ring (7) and make

sure it is fully seated in its groove.

AXLE SEAL

1. The seal (75) can be replace by following

steps 2-6 of the procedure used to replace
the input seal.

2. Install the retaining ring (116) and make sure

it is fully seated in its groove.

MOTOR SHAFT SEAL

1. Remove the brake assembly. See Pages

17-18.

2. The seal (84) can be replaced by following

steps 3-6 of the procedure used to replace
the input shaft.

TRUNNION SEAL

1 Remove the control arm and any at tach -

ments to the control arm. See Page 20.

2. The seal (33) can be replaced by following

steps 3-6 of the procedure used to replace
the input shaft.

BYPASS SEAL

1. Remove the bypass arm and any at tach -

ments to the bypass arm. See Page 19.

2. Remove the bypass rod seal (40). Deburr

the bypass rod.

3. Install the seal (40). Install the bypass arm

(41) and retaining ring (42).

Figure 16. Seal Replacement Kit

REF. Part Name

1  Main Housing
5  Lip Seal
7  Retaining Ring
33  Lip Seal
40  Lip Seal
41  Bypass Arm
42  Retaining Ring
75  Seal
84  Lip Seal
116  Retaining Ring

«
...
22
23
24
25
26
...
»

Содержание 310-1500

















































Отзывы:

Нет отзывов

Похожие инструкции для 310-1500

Бренд: BTC Страницы: 22

Бренд: Danfoss Страницы: 10

ACE-tronics G9 ASD

Бренд: Toshiba Страницы: 297

Бренд: Yamaha Страницы: 24

CRW4416E - CRW - CD-RW Drive

Бренд: Yamaha Страницы: 25

CRW4416S - CRW - CD-RW Drive

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 24

CRW8824FXZ - CD ROM Drive

Бренд: Yamaha Страницы: 44

PORTATONE KB-280

Бренд: Yamaha Страницы: 47

CRW8824SX - CRW 8424SX - CD-RW Drive

Бренд: Yamaha Страницы: 46

CRW8424SX Series

Бренд: Yamaha Страницы: 46

CRW8424E Series

Бренд: Yamaha Страницы: 46

CRW3200SX Series

Бренд: Yamaha Страницы: 46

CRW3200UX Series

Бренд: Yamaha Страницы: 48

CRW2200UX Series

Бренд: Yamaha Страницы: 45

CRW3200IX Series

Бренд: Yamaha Страницы: 50

CRW2200SX Series

Бренд: Yamaha Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды