Hydro-Gear 310-1500 Скачать руководство пользователя страница 47

Страница: 47 / 48

-1500/-1700 IHT

Hydrostatic Transaxle:

A multicomponent as sem bly including a gear case and a hydrostatic

trans mis sion.

Hydrostatic Transmission:

The combination of a hy drau lic pump and motor in one housing to

form a de vice for the control and transference of power.

Inlet Line:

A supply line to the pump.

Integrated Hydrostatic Transaxle (IHT):

The com bi na tion of a hydrostatic transmission and

gear case in one housing to form a complete transaxle.

Manifold:

A conductor which provides multiple con nec tion ports.

Neutral:

Typically described as a condition in which

uid

ow and system pressure is below that

which is required to turn the output shaft of the motor.

Pressure Decay:

A falling pressure.

Priming:

The

lling of the charge circuit and closed loop of the

uid power system during start

up, fre quent ly achieved by pressurizing the

uid in the inlet line.

Purging:

The act of replacing air with

uid in a

uid power system by forcing

uid into all of the

com po nents and allowing the air a path of es cape.

Rated Flow:

The maximum

ow that the power sup ply system is capable of maintaining at a

spe ci

c op er at ing pressure.

Scoring:

Scratches in the direction of motion of me chan i cal parts caused by abrasive con tam i-

nants.

Swash Plate:

A mechanical device used to con trol the displacement of the pump pistons in a

uid power sys tem.

System Charge Check Valve:

A valve con trol ling the replenishing

ow of

uid from a charge

circuit to the closed loop in a

uid power system.

System Pressure:

The pressure which over comes the total resistance in a system, in clud ing

all losses.

Valve:

A device which controls

uid

ow di rec tion, pressure, or

ow rate.

Variable Displacement Pump:

A pump in which the displacement per cycle can be varied.

Volumetric Displacement:

The volume for one rev o lu tion.

Содержание 310-1500

















































Результаты поиска

Содержание 310-1500

Отзывы:

Похожие инструкции для 310-1500

Бренды по названию

Популярные бренды

Hydro-Gear 310-1500, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание 310-1500

Отзывы:

Похожие инструкции для 310-1500

Бренды по названию

Популярные бренды