Hydro-Gear 310-1500 Скачать руководство пользователя страница 39

Страница: 39 / 48

-1500/-1700 IHT

Figure 28. Directional Control Assembly

DIRECTIONAL CONTROL
ASSEMBLY

Refer to Figure 28.

NOTE: The Motor/Center Section/Pump
Assembly must be disassembled before
this procedure can be completed.

DISASSEMBLY

1. Remove swashplate assembly (10). Dis as-

sem ble swashplate assembly by removing
thrust bearing (11) from swashplate (10). The
thick race of thrust bearing must face pis tons.

2. Remove slot guide (30) from the trunnion

arm (31).

3. Remove the trunnion arm (31) from the main

housing (1).

INSPECTION

1. Visually inspect (in place) the two cradle

bear ings (9), which are staked in main hous-
ing. Do not remove the Cradle Bearings (9)
from housing (1).

ASSEMBLY

1. Install the trunnion arm in the main housing

(1).

2. In

stall slot guide (30) onto the trunnion arm

(31).

3. As

sem ble swashplate as sem bly (10) by in-

stall ing thrust bearing (11) into swashplate
(10).

Note: As sem ble thrust bear ing with thick
race fac ing pistons.

4. Install swashplate assembly (10) into main

housing (1). The swashplate (10) will couple
with slot guide (30).

NOTE: When in stall ing swashplate as-
sem bly (10), use

at head screwdriver

to hold slot guide (30) in place.

5. Rotate the trunnion arm to con

rm proper

swashplate movement.

REF. Part Name

1   Main Housing
9  Cradle Bearing
10  Variable Swashplate
11  Thrust Bearing
30  Slot Guide
31  Trunnion Arm

Содержание 310-1500

















































Результаты поиска

Содержание 310-1500

Отзывы:

Похожие инструкции для 310-1500

Бренды по названию

Популярные бренды

Hydro-Gear 310-1500, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание 310-1500

Отзывы:

Похожие инструкции для 310-1500

Бренды по названию

Популярные бренды