HydraMaster CDS 4.6 Скачать руководство пользователя страница 27

Страница: 27 / 126

operating Instructions: 3-4

3 speed Throttle Control function

▬

For gM Vans

▬

The GM Throttle Controller must meet certain “Chassis Ready” conditions to elevate the

engine rpm, which are as follows:

Parking Brake is set

Gear shift is in “Park”

foot is off Service Brake (brake pedal)

foot is off Accelerator Pedal

Vehicle is stationary (no speed)

engine is started and idling

The A/C / Heater switch is in off position

The Throttle Controller must be initialized anytime the Data link Cable (DlC) harness is

disconnected from the Data link Connector. To initialize the system switch ignition key to

off position, plug in DlC harness, switch the ignition on, and then start the engine. This

allows the Throttle Controller to read the PCM engine computer.

on the Throttle Controller, there are leD lights with corresponding labels to provide status

and problem detection information (refer to figure 3-1 and Table 3-1).

Location of Controller’s LED Lights

Figure 3-1.

with Labels and RPM Trim Potentiometers

3 TRIM POTS

LED LIgHTS WITH

LABELS

Содержание CDS 4.6































































































































Результаты поиска

Содержание CDS 4.6

Отзывы:

HydraMaster CDS 4.6, Руководство пользователя, Страница: 27 / 126

Результаты поиска

Содержание CDS 4.6

Отзывы: