HydraMaster CDS 4.6 Скачать руководство пользователя

Страница: 113 / 126

9-5: electrical System

electrical Troubleshooting

1.0. CDS WILL NOT TURN ON

1.1. The main power fuse

has blown.

Remove CDS cowling and engine cover and check all

wiring from the power source back to the CDS console

for damage. Replace fuse only after locating the problem

that caused the fuse to blow. If unable to locate problem,

refer to qualified service technician.

1.2. The plug-in connection

at the base of the recovery

tank is corroded.

Clean and seal connection to protect it from moisture.

1.3. The main circuit breaker

has blown on the CDS

dash..

Reset breaker and look for loose connections or damaged

wires. Check all wires from the control panel forward to

the front of the vehicle. If no problem is found but the

breaker still trips refer to qualified service technician.

2.0. CDS SHUTS OFF WHILE IN USE

5.1. Recovery tank is full.

empty tank and restart machine.

5.2. Recovery tank float

switch is dirty or defective.

Inspect float to see if the triangle mark on the float is

facing up. If it is, and the float slides freely on the post,

replace the float assembly.

5.3. The vehicle gear selector

has moved.

Inspect the gear selector to be sure it is in the proper

position. If selector has moved, refer to qualified service

technician.

If vehicle gear selector has moved, refer to qualified service technician. This is a

dangerous condition and needs to be repaired immediately.

Содержание CDS 4.6































































































































Результаты поиска

Содержание CDS 4.6

Отзывы:

Похожие инструкции для CDS 4.6

Бренды по названию

Популярные бренды

HydraMaster CDS 4.6, Руководство пользователя

Результаты поиска

Содержание CDS 4.6

Отзывы:

Похожие инструкции для CDS 4.6

Бренды по названию

Популярные бренды